| Part # |
Description |
| 269A3150-5-80901 |
 Adapter Lower Cap & T Pin Landing Gear |
| 269A3150-5-80903 |
 Landing Gear Wrench Adapter |
| 269A3150-5-80904 |
 Torque Wrench Adapter Landing Gear |
| 269A3162-3-MT-1-1-12 |
 Piston Guide Damper Tool |
| 269A3162-3-MT-1-1-20 |
 Piston Guide Damper Tool |
| 269A5510-3-80901 |
 Short Shaft Alignment Tool |
| 269A6300-80901 |
L/G Damper Overhaul Charging Tool Complete |
| 269A6300-80901-1 |
 Nitrogen Charging Kit |
| 269A9206 |
 Wrench Adapter |
| 269A9213 |
Punch, Brg. Installation |
| 269A9215 |
 Thimble Oil Seal |
| 269A9216 |
 Punch 07412 Seal Installation |
| 269A9219 |
Punch 71B7512 & 63X233 Seals |
| 269A9221 |
 Punch & Drift 269A5050-13 Brg. Install |
| 269A9222 |
 Install Brg. Punch |
| 269A9224 |
 Wrench NAS1441-9 Locknut Installation |
| 269A9227 |
Supt. Assy. Dial Indicator |
| 269A9228 |
 Wrench, Nut M/R Thrust |
| 269A9230 |
Seal Instl. Thimble |
| 269A9232 |
 Plug |
| 269A9233 |
 Plug 269A5050-12 Brg. Removal |
| 269A9235 |
Tool 269A5509 Retainer Installation |
| 269A9236 |
 Plug 269A5050-14 Brg. Removal |
| 269A9237 |
 Tool NAS1443-9 Lockwasher Installation |
| 269A9238 |
 Plug 269A5050-15 Brg. Removal |
| 269A9241 |
 Punch & Block 269A5050-44 Brg. Installation |
| 269A9247 |
 Plug, Cone Installation used on 269A5050-010 |
| 269A9248 |
 Sleeve, Cone Installation used on 269A5050-010 |
| 269A9257 |
Int. Puller -Main Trans. Brg. |
| 269A9258 |
 M/GBox Pinion MS172338 Nut Wrench |
| 269A9263 |
 Installation Sleeve |
| 269A9264 |
 Wrench 269A5608 Nut Instl. T/R |
| 269A9267 |
Comb. Puller Assy. (3 Jaw) Main Xmsn. |
| 269A9279 |
 Punch 63X233 Seal Installation |
| 269A9280 |
 Punch 71B7512 Seal Installation |
| 269A9282 |
 Punch 269A5050-19 Brg. Installation |
| 269A9291 |
 Wrench Adapter Preload LS Shaft |
| 269A9294 |
Overhaul Tool 269A5174 Brg Oil Pump |
| 269A9296 |
 Bar Assy. -269A5050-11 Brg. Clip Removal |
| 269A9297 |
 Tool Block Landing Gear Damper Strut Assy |
| 269A9338 |
Plug 269A5050-15 Brg Removal |
| 269T1000 |
Magnetic Pick-Up Bracket |
| 269T1005 |
 Comp. Check Spline Adpt. Engine Turning Tool |
| 269T1179 |
Arbor Press & Stk. Tool for 269A5050-61 Brg. Includes: |
| RB0006-809-00090-8 |
 Arbor Press |
| RB0006-809-00090-20 |
Staking Tool |
| 269T1221 |
 Socket Pitch Brg. Locknut M/R |
| 269T3301 |
 |
330 Engine Lift |
|
| 269T3303 |
 Engine Alignment Tool "330/333" Models |
| 269T3303-003 |
 Pulley Assy Installation/Alignment Tool |
| 269T3313 |
Adapter |
| 269T3320 |
 Upper Pulley Hub Holding Tool |
| 269T3321 |
 Upper Pulley Cap Pressing Tool (2 Pieces) |
| 269T3330-03 |
 Installation Aid |
| 269T9203-7 |
 Rigging Fix. Cyclic Stick Centering (Left) |
| 269T9203-11 |
 Rigging Fix. Cyclic Stick Centering (Right) |
| 269T9203-19 |
 Rigging Fixture Cyclic Stick Centering |
| 269T9204 |
 Rigging Tool T/R Low Tip Speed |
| 269T9204-3 |
 Rigging Tool T/R Low Tip Speed |
| 269T9204-5 |
 Rigging Tool T/R Low Tip Speed |
| 269T9205 |
 Wrench Main G/Box |
| 269T9211-003 |
 Drive Shaft Coupling Adapter Spanner Wrench |
| 269T9211-005 |
 Wrench Adapter Spanner |
| 269T9213 |
 Punch, Brg. Installation |
| 269T9218 |
Fuel Injector Tool (same as: RB23007638) |
| 269T9231 |
 Wrench 269A1340 Nut |
| 269T9239 |
 Puller 993J07X3E |
| 269T9246 |
 Support Main Xmsn. 269A5103 Pinion |
| 269T9259 |
 Micrometer Lead Lag & Flapping Hinge |
| 269T9269 |
 Rigging Tool |
| 269T9269-5 |
 Lateral Rigging Tool |
| 269T9269-9 |
 Rigging Tool |
| 269T9270 |
 Long Cyclic Rigging Fixture |
| 269T9272-5 |
 M/R Rigging Block |
| 269T9275-003 |
 T/R Nut Wrench |
| 269T9276 |
 Installation Rod, T/R Drive Shaft |
| 269T9278 |
 Tube M/R Drive Shaft |
| 269T9281 |
 Wrench, Splined Fitting |
| 269T9284 |
Installation Tube Upper Fwd Bearing |
| 269T9286 |
 Rigging Aid T/R Control |
| 269T9299 |
 Wrench Lower Pulley Shaft |
| 269T9300 |
 Wrench, Washer Installation |
| 269T9302 |
 Wrench, Upper Pulley Adjustment |
| 269T9303-003 |
 Wrench, Upper Pulley Adjustment |
| 269T9307 |
 Wrench 269A6258 Locknut Installation |
| 269T9308-001 |
 Wrench Assembly For Flapping Hinge |
| 269T9310 |
 Micrometer Flat Hinge |
| 269T9312 |
 Wrench Install 269A1315 Nut |
| 269T9319 |
 |
Wrench, T/R Bushing (Same as: RBA1600-80902) |
|
| 269T9320 |
 T/R Pitch Control Staking Tool |
| 269T9322 |
Tab Bender Same As: RBH9928 |
| 269T9330 |
 Socket 269A6029 Nut Drive Spline T/R G/Box |
| 269T9331 |
 Idler Pulley Brg. Locknut Installation |
| 269T9336-101 |
 Lower Pulley Puller |
| 269T9336-103 |
 Upper Pulley Shaft Brg. Puller |
| 269T9336-105 |
 Pulley Bearing Screw Set |
| M34005850 |
Same As Part # : 269A6300-80901-1 |
| M4000680 |
Same As: RBA9937-5 |
| M40021050 |
Same As: RBT18605 |
| M40070304 |
Same As: 6798292 |
| M40070308 |
Same As: 6886204 |
| M40071100 |
Same As: 23003267 |
| M40071200 |
Same As: 23007638 |
| RBT18541 |
Landing Gear Damper Instl./Remove Tool |
| RBT18646 |
 Engine Support Strut For 330 |
| RBT18803 |
Lower Coupling Dr Shaft Instl./Remove Tool |
| RBT18801 |
T/R Output Gear Holding Fixture TH55 |
| RBT18805 |
T/R Xmsn. Input Brg. Rem. Tool |
| RBT18809 |
Socket 9/16" - 12PT |
| TH-55 |
Replaced By: RBT18801 |
